*Note: Version updates require synchronous firmware upgrades to the specified version; otherwise, incompatibility errors will occur.
Version Information Synchronization Table (Please ensure you upgrade to the specified versions)

Version: 2025.11.17-release
- SAStudio4 Version: 4.3.55.30
- API Version: 0.55.63
- MCU Version: 0.55.64
- FPGA Version: 0.55.28
- Bus Version: 0.55.6
- EIO Version: 1.16

Version: 2025.11.04-release
- SAStudio4 Version: 4.3.55.30
- API Version: 0.55.63
- MCU Version: 0.55.62
- FPGA Version: 0.55.28
- Bus Version: 0.55.6
- EIO Version: 1.16

Version: 2025.10.17-release
- SAStudio4 Version: 4.3.55.29
- API Version: 0.55.63
- MCU Version: 0.55.61
- FPGA Version: 0.55.28
- Bus Version: 0.55.6
- EIO Version: 1.16

- Updater_0_55_63_V4 (11/17/2025)
*After using this version of the Updater, the firmware will be updated to: MCU 0.55.64, FPGA 0.55.28, BUS 0.55.6, EIO 1.16
*Added: Restrict firmware updates to Bus versions below 0.55.3 (excluding 0.55.3) to ensure no software compatibility issues arise.
*Fixed: The M80 R5 exhibits temperature-dependent spurious emissions in the 6GHz-7GHz band.
*Fixed: Incorrect power and background noise on E200 R4 at frequencies below 150MHz.

- Updater_0_55_63_V3 (11/7/2025)
*After using this version of the Updater, the firmware will be updated to: MCU 0.55.62, FPGA 0.55.28, BUS 0.55.6, EIO 1.16
*Optimized: Improved residual response performance below 3 GHz on N400 R2V2 devices.

- Updater_0_55_63_V1 (10/18/2025)
*After using this version of the Updater, the firmware will be updated to: MCU 0.55.61, FPGA 0.55.28, BUS 0.55.6, EIO 1.16
*Added: NX devices support remote update of FX3 firmware
*Optimized: PNM to improve the speed of non-DS segment configuration
*Optimized: Improve IM3 function measurement accuracy
*Optimized: Optimize the connection stability of NX devices in weak network environment, and solve the problem of reconnection after abnormal disconnection.
*Fixed: The problem that the edge cannot be locked when triggered by the rising edge of the level.
*Fixed: The problem of timeout when the trigger delay is greater than the pulse signal period.
*Fixed: The problem that GNSS information cannot be obtained in the first packet of data.

- Updater_0_55_61_V11 (07/16/2025)
*After using this version of the Updater, the firmware will be updated to: MCU 0.55.57, FPGA 0.55.22, EIO 1.15
*Fixed issue with NX devices returning error code -21 during updates

- Important version update, configuration time reduction(up to 5ms)
*FX3 version 0.55.1 or higher
*MCU version 0.55.52 or higher
*FPGA version 0.55.22 or higher
*All three conditions must be met to achieve 5ms configuration time

- Updater_0_55_61_V10 (07/09/2025)
*After using this version of the Updater, the firmware will be updated to: MCU 0.55.56, FPGA 0.55.22, EIO 1.15
*Initial release
*Currently supports only devices with MCU and FPGA versions 0.55.0 and above
*All SA devices are currently allowed to update
*All NX devices are currently not allowed to update
*PX devices are only allowed to update for specific versions
*For detailed update rules, please refer to the README.txt file in the update package