- Updater_0_55_63_V1 (10/18/2025) * MCU firmware replaced with version 0.55.61 * FPGA firmware replaced with version 0.55.28 * NXserver replaced with latest version *Added: NX devices support remote update of FX3 firmware *Optimized: PNM to improve the speed of non-DS segment configuration *Optimized: Improve IM3 function measurement accuracy *Optimized: Optimize the connection stability of NX devices in weak network environment, and solve the problem of reconnection after abnormal disconnection. *Fixed: The problem that the edge cannot be locked when triggered by the rising edge of the level. *Fixed: The problem of timeout when the trigger delay is greater than the pulse signal period. *Fixed: The problem that GNSS information cannot be obtained in the first packet of data. -Updater_0_55_61_V11 (07/16/2025) * MCU firmware updated to version 0.55.57 * Fixed issue with NX devices returning error code -21 during updates -MCU 0.55.57 (07/14/2025) * Bug fixes: Added update command verification and enhanced handling of abnormal interruptions. Improved resilience against data anomalies (helps resolve issues where devices return error code -8 and cannot recover) - Updater_0_55_61_V10 (07/09/2025) * Initial release * Currently supports only devices with MCU and FPGA versions 0.55.0 and above * All SA devices are currently allowed to update * All NX devices are currently not allowed to update * PX devices are only allowed to update for specific versions * For detailed update rules, please refer to the README.txt file in the update package - MCU 0.55.56 (07/02/2025) * Bug Fix: Resolved power drop issue at certain frequencies on SAM devices - MCU 0.55.54 (06/06/2025) * Added: Trigger edge selection adjustment - Important version update, configuration time reduction(up to 5ms) * FX3 version 0.55.1 or higher * MCU version 0.55.52 or higher * FPGA version 0.55.22 or higher * All three conditions must be met to achieve 5ms configuration time - MCU 0.55.53 (05/07/2025) * Added: Support for E200 R4 devices * Optimization: Adjusted in-band flatness for M80 * Bug Fix: Adjusted switch response delay for M60 series * Bug Fix: Fixed firmware update issue for eioz - FPGA 0.55.22 (05/07/2025) * Added: Upgraded control bus to bulk mode - MCU 0.55.50 (04/17/2025) * Added: eio_zbms information * Bug Fix: Added VGA power response delay for E90 (to avoid DS overflow) - FPGA 0.55.19 (04/21/2025) * Upgraded: Control bus mode to improve speed - MCU 0.55.49 (04/17/2025) * Added: PNM support * Made calibration trigger method configurable * Added: EIO_Z BMS information * Bug Fix: Fixed DCLB demod power switch issue for SAM series * Bug Fix: Corrected DS section start frequency calibration - FPGA 0.55.18 (04/14/2025) * Added: PXZ battery management feature - FPGA 0.55.17 (04/14/2025) * Added: PhaseNoiseMeas functionality - MCU 0.55.48 (02/07/2025) * Bug Fix: Unified NCO correction; correction applied when span is below 100 MHz - MCU 0.55.47 (01/13/2025) * Bug Fix: Resolved low power measurement issue at 30 MHz on SAM series - MCU 0.55.46 (01/10/2025) * Bug Fix: Fixed power drop issue around 34 GHz on N400 devices * Bug Fix: Optimized close-in spurious suppression via LO strategy adjustment - MCU 0.55.45 (01/02/2025) * Added: PNM mode * Added: MPS mode (does not affect other frequency mode functions) * Bug Fix: Resolved phase noise degradation at 1G/3G with 1 MHz offset - MCU 0.55.44 (12/23/2024) * Added: Hardware modification in N400 R2 compared to 0.55.40; adjusted DS section switch delay to 100 µs - MCU 0.55.43 (12/19/2024) * Bug Fix: Fixed missing HCD update introduced during merging - MCU 0.55.42 (12/17/2024) * Added: MPS mode * Added: Enhancements to PNM mode * Added: DS section delay changed to 100 µs for N400R2V2 devices - MCU 0.55.40 (10/31/2024) * Bug Fix: Fixed multi-PLL mounting and communication mode switching issues on M10 (ensures M60 signal source remains locked during continuous sweep) * Bug Fix: Proper control of GNSS trigger source - MCU 0.55.39 (09/20/2024) * Added: Hopping delay during calibration now controlled by host * Added: Optimized 4002 lock detection logic and improved initial configuration speed * Bug Fix: Separated GNSS info parsing and uploading to resolve GNSS time jump issue * Bug Fix: Fixed DS section 9k–10M frame stitching logic - MCU 0.55.38 (07/17/2024) * Added: Lowsidelobe window type for low phase noise measurement * Bug Fix: Fixed NCO correction bug (hard boundary caused signal shift when changing window types)